
Two measurements settle whether you need a 1310 or 1350 u-joint: the outside diameter of the bearing caps, and the width across the joint from one cap to the opposite cap. A 1310 has 26.99 mm caps and measures 81.76 mm across. A 1350 has 30.16 mm caps and measures 92.08 mm across. Take both readings, because a third series, the 1330, shares its caps with the 1310 and its width with the 1350.
Those figures come from the Hardy Spicer Driveshaft Component Catalogue, which lists universal joint kits by cap diameter and width.

A universal joint, or uni joint, is the cross-shaped joint at the ends of many tailshafts. Each of its four arms carries a bearing cap, also called a cup, which holds the needle rollers. The caps sit in the ears of a yoke, the forked part on the shaft, gearbox or diff that the joint connects to.
Measure the joint itself, either one out of the shaft or a new joint in your hand. Take three readings:
These follow the measuring advice on our own FAQ page for conversion joints. Hardy Spicer’s catalogue identifies its kits the same way, by cap diameter, width, and the type and number of caps. Both say to measure with the caps compressed, and the catalogue adds a caution not to dislodge the needle rollers while you do it.
Use vernier or digital calipers, not a tape measure. Some of the differences that matter here are less than 2 mm.

The catalogue prints these dimensions for its 1310, 1330 and 1350 series kits. The inch figures are conversions of the millimetre values.
Read across the rows and the 1330 problem is plain. Measure only the width and a 1330 reads as a 1350. Measure only the caps and it reads as a 1310. With both readings, each series has its own pair of numbers.
| Series | Cap diameter | Width across the caps |
|---|---|---|
| 1310 | 26.99 mm (1-1/16 in) | 81.76 mm (3-7/32 in) |
| 1330 | 26.99 mm (1-1/16 in) | 92.08 mm (3-5/8 in) |
| 1350 | 30.16 mm (1-3/16 in) | 92.08 mm (3-5/8 in) |
The gap between a 1310 cap and a 1350 cap is 3.17 mm, about an eighth of an inch. On a bench, or in a photo, the two joints look much the same. The width is the second check: a 1350 is 10.32 mm wider across the caps than a 1310.

Some joints carry two cap sizes on one cross. Hardy Spicer lists 1310 joints for some Ford applications with two caps at 26.99 mm and two at 28.58 mm (1-1/8 in). Both directions still measure 81.76 mm across, the same as a standard 1310.
On those joints the width gives no warning at all. The only sign is one pair of caps that is 1.59 mm larger than the other pair. Measure one cap, or one pair, and you can end up ordering the wrong joint.
A conversion joint is the deliberate version of the same idea. It carries one series’ caps on one axis and another series’ caps on the other, for a shaft and a yoke of different series, such as a 1330 tailshaft meeting a 1350 rear yoke. The catalogue’s 1330 to 1350 conversion measures 92.08 mm in both directions, so only the caps show which axis is which. Our FAQ page explains what a conversion joint is and how to measure one.

Clips, which the catalogue calls snap rings or circlips, keep each bearing cap in place in its yoke ear. A joint can have outside clips, inside clips, or one style on each axis. Clip style is a separate check from series, so note it for each pair of caps.
Look at the caps as well. Hardy Spicer’s catalogue lists several round cap types, including grooved and plain, and records the type for each axis. Some of its kits carry a different cap type on each axis, so write the type down beside each cap size.
Clip position can also change how a width is read. Among the catalogue’s notes is one for kits whose width is measured from the inside face of one snap ring to the inside face of the opposite ring, rather than across the caps. If your reading falls between two sizes, check how that joint was measured before you decide.

With all four caps, both widths and the clip style written down, you have the details needed to match the joint. The same readings answer the ‘Rear U-Joint’ and ‘Cup Diameter’ fields on our tailshaft order forms. If you are measuring a complete shaft rather than one joint, our article on ordering a custom tailshaft from interstate explains the other dimensions to take.
The measurements identify a series. They do not tell you which joint a particular vehicle takes, and a joint that reads between two sizes needs a second look. In either case, send your readings through the quote form rather than guess. Once the series is clear and all four caps agree with it, you can browse universal joints in the GJ Drivelines online store.




Chrysler – Dodge
727 – 30 Spline 1 11/16″ Seal Diameter
904 – 26 Spline 1 9/16″ Seal Diameter
Ford
C6-T56 – 31 Spline 1 11/16″ Seal Diameter
AOD & C4 & T5 – 28 Spline 1 1/2″ Seal Diameter
4 R 7OW – 28 Spline 1.598″ Seal Diameter
General Motors
T-350 700R4-4LLOE – 27 Spline 1 1/2″ Seal Diameter
T-400-4L80E – 32 Spline 1 7/8″ Seal Diameter
Note: Transmission slip yokes are manufactured with various U-Joint Series. It is important to match Horsepower and Torque requirements to U-Joint Series. For aftermarket transmission applications usually a spline count and seal diameter will identify slip yoke required.

If Pinion Yoke has Placement tabs that retain the U-Joint, measure inside tabs. See Diagram D.

If Pinion Yoke does not have Placement Tabs that retain U-Joint, measure from flat of yoke inside to inside. See Diagram E.

If 4 bolt Flange is used on pinion, measure Pilot Diameter and center to center diagonally bolt hole to bolt hole. See Diagram L.

Universal Joint Size. There are hundreds of U-Joint sizes or “Series” to accomodate many different applications of power and desired longevity for your automotive, 4×4 truck or auto racing requirements, these 4 series of joints cover most needs.
1310 Spicer Series: 1 1/16″ Cup Diameter (Dim C – Diagram A) 3 7/32″ length (Dim B – Diagram A) Certain Ford applications have 2 cups 1 1/8 Diameter. Appropriate horse power range is up to 500 in circle track or road racing, small tire drag racing and 4×4. Also available: Performance Dynamic Cryo Joint.
1330 Spicer Series: 1 1/16″ Cup Diameter (Dim C – Diagram A) 3 5/8″ length (Dim B – Diagram A) Certain Ford applications have 2 cups 1 1/8 Diameter. Slightly stronger than 1310, Used in 5.0 Mustangs. Also available: Performance Dynamic Cryo Joint.
3R Saginaw Series: 1 1/8″ Cup Diameter (Dim C – Diagram A) Retained with internal clip 2 5/8″ (Dim B – Diagram A). Most common GM joint. Horse power range up to 700 in road racing and circle track. Solid drag racing U-Joint can accomodate most sportsman classes. Also available: Performance Dynamic Cryo Joint.
1350 Spicer Series: Manufactured with OEM tolerances and treated with our Cryogenic Process to yeild the strongest U-Joint available. For drag racing applications a solid non-lube design U-Joint is recommended because of the tremendous initial shock load, or short duration of high torque the joint must be able to withstand.

If PST is supplying you with transmission slip yoke, Pinion yoke and driveshaft yoke measure Dim W. See Diagram N.
If PST is supplying you with transmission slip yoke and driveshaft measure Dim X. See Diagram N.
2 Piece driveshafts use Dim Y + Z. See Diagram N.